DIN EN 10243-1 PDF

Find the most up-to-date version of DIN EN at Engineering Buy DIN EN STEEL DIE FORGINGS – TOLERANCES ON DIMENSIONS – PART 1: DROP AND VERTICAL PRESS FORGINGS. Standard DIN EN Steel die forgings – Tolerances on dimensions – Part 1: Drop and vertical press forgings; German version EN.

Author: Malatilar Zulubei
Country: Germany
Language: English (Spanish)
Genre: Travel
Published (Last): 4 April 2016
Pages: 40
PDF File Size: 5.17 Mb
ePub File Size: 14.95 Mb
ISBN: 225-3-93697-504-6
Downloads: 80021
Price: Free* [*Free Regsitration Required]
Uploader: Faur

From Table 1 the tolerances see Figure 20 are found to be: They shall be taken from Table 1 and Table 2. The horizontal line is then followed to the right.

DIN EN 10243-1

Users are responsible for its correct application. For centre-to-centre dimensions greater than 1 mm length, tolerances from Table 1 or Table 2, with equal plus or minus dispersions, shall be applied. Only tolerances to 10243-11 F shall be applied. VanDeusen Wisc B Documents. In such cases the minus tolerance is modified to allow for the formation of a square corner.

ISOTechnical drawings Fundamental tolerancing principle.

EN 10243-1.pdf

By further movement to the right, the correct tolerance is found under the appropriate vertical column heading for the dimension concerned wherever possible the greatest dimension of length, width or height see 5. If the category of steel used is M1, the same horizontal line is followed further to the right. Base all thickness tolerances except those for overall thickness on dimension t shown above. The characteristics of the forging process require that, for any given forging, all tolerances for thickness dimensions are uniform.

DIN EN – Free Download PDF

This European Standard does not apply to upset forgings made on horizontal forging machines see EN For dimensions from a centre to a surface see Figure 9 and for dimensions on steps within one die, the tolerances for the greatest length, width and height shall apply wherever possible. This special procedure is not applied if larger tolerances 102431- result from use of the normal procedure as shown in 4.

  CHOMANA DUDI PDF

This European Standard is considered to be a supporting standard to those application and product standards which in themselves support an essential safety requirement of a New Approach Directive and which make reference to this European Standard. Instances occur in which the negative tolerances for such local deviations cannot be permitted on unforged stock where it is not subsequently machined.

Tolerances for heavier or larger forgings shall be agreed at the time of enquiry and order. When straightness tolerances or flatness tolerances are required, this shall be indicated on the agreed forging drawing.

Normally the tolerances for the greatest dimension of length or diameter of the forging will be applied but, if more restrictive tolerances are required, those for the specific dimension of the pierced hole may be used. S3Type of steel used: Ejector mark tolerances are applied independently of, and in addition to, any other tolerances. See us on booth at NPE Documents. These two grades of tolerances are identified as follows: Los resortes de troquel MDL estn diseados para ser intercambiables con los resortes de Danly y otros Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member.

A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the English versionSteel die forgings Tolerances 102243-1 dimensions Part 1: Tolerances for fillet and edge radii shown in Table 6 are applicable to both grade E and grade F. The tolerances specified apply to forgings not exceeding kg in mass or 2 mm maximum dimension.

  LSI MEGARAID SAS 9260-4I PDF

Such special tolerances shall be agreed between the supplier and the purchaser before the commencement of production. The supplier will draw the attention of the purchaser to such instances and it will be necessary to negotiate greater tolerances on the draft angle surfaces to meet these circumstances.

The shape complexity factor of a forging dkn the ratio of the mass of the forging to the 12043-1 of the enveloping shape necessary to accommodate the maximum dimensions of the forging: The weight of the total length in question shall be calculated as if of unforged stock, irrespective of whether this is the case or not.

Mismatch tolerances depend on the forging mass and on the shape of die line. Eccentricity tolerances for deep holes shall be applied in addition to the normal tolerances for mismatch see Figure Straightness and flatness tolerances are applied independently of, and in addition to, any other tolerances. They are best dealt with by consultation at the design stage rn shall be agreed between the purchaser and the supplier.

The first part of this European Standard applies to hot forgings in the delivery condition, made in carbon and alloy steels.