JTAG PANTEC PDF

Pantech Solutions. Online Retail store for Trainer Kits,Lab equipment’s,Electronic components,Sensors and open source hardware. This process is to assist in the repair of your Pantec receiver. There are 2 We need to Build a JTAG cable and we need to modify the receiver. To modify the. have performed the JTAG operation on my Pansat A using both Skymax and jKeys .. The first thing to do here is figure out if you have a PanTec MX or MS.

Author: Kebei Garg
Country: Maldives
Language: English (Spanish)
Genre: History
Published (Last): 18 May 2005
Pages: 83
PDF File Size: 4.95 Mb
ePub File Size: 14.49 Mb
ISBN: 558-1-83591-616-3
Downloads: 31077
Price: Free* [*Free Regsitration Required]
Uploader: Akinogar

Lab4 SD card Audio Player: Review the Application Code Step 8: The easiest was to make the cable is to take a serial pass through cable and cut it about 3 feet from the male connector end.

Don’t scrape traces and don’t attempt to solder to the cpu. Configure the Camera and Related Modules Step 5: Your receiver will work at this point. I have read about the buffered JTAG cable and I built one and found no difference in process itag effectiveness.

Which jtag is best for pantec mx

Gently remove the receiver board from the case. Next you want to add the fan.

Review the Application Code Step Again don’t be worried or surprised if the bin doesn’t load or the file errors, wait for the reboot Click here to edit contents of this page. I used a meter and found the tab by the transister as shown below. Generate Harmony code Step 7: Waking up the receiver: Also make sure that you jjtag place the board inside the box and put the lid on.

  ESANSIYEL TROMBOSITOZ PDF

Make sure you heat shrink the resister. The receiver should be switched off but plugged in. Put the header strips through the holes on the patnec and re solder the pins on the underside of the board.

Bend the leads so the parts won’t fall out psntec don’t solder them yet.

PANTEC MS REPAIR

You can buy it separately but you will find it in a kit with everything you need. There is no standard JTAG connector or pinout, so suppliers are able to define their own. Put a very small amount of solder on the ends of the wire.

Follow these steps and you can use it again. Analog Sensor Conditioning Additional content planned Remove the case screws and remove the top panel of the case. Expand copy the appropriate files to their directories. Now the good news is that the receiver isn’t dead You will also require the 9 pin female to 9 pin female serial Straight through cable that came with your receiver.

Pantec FTA Files & Pantec FTA KEYS

Examine the photo below and make sure your looking at pin and The comctrl32 used in XP may effect the operation of the VB scripting. For this step of the procedure, you will need the following parts. No big balls of solder are allowed.

  JURNAL AMPHIBI PDF

Remove the corner screw and place the header board on top then put the screw through the perf board and re tighten it. Feel the heat from the unit and see how hot it gets. Gently rest the resister end on top of one solder pad on the board. I think cheaper is always better.

The process window will appear. Add Existing Items From Folders Remove the coax cable connector rings.

Power up the unit and confirm that it still turns on and goes beyond the night rider stage. The next part is the ground for the resister.

Unplug the gray cable from the center socket near the CPU. Examine the diagram below Locate the following tabs on your receiver If your machine is a MX go here.

Its easy to make them touch. Don’t put the tape on the heat sink first. If an error message appears, repeat the process. The cathode of the 1N goes to ground.

Configure Evaluation Board Step 4: Unplug the pantce cable. Review the Application Code Step 6: Cut the excess wires off and clean up the board. This isn’t absolutely necessary but a good idea.